Category Archives: Canopy

Time: 2 Hours

When you fly the RV-8 without a passenger it is pretty hard to reach all the way back to grab the canopy and slide it closed. So builder usually put some sort of stop so that the canopy catches and stops just behind the pilot which makes it easier to grab and close. I decided that I like the FlyBoys latch and this is how I installed it. The idea is that there is a free swinging teardrop shaped plastic piece that gets bolted to the canopy frame at the roller connection point. FlyBoys gives you the required pieces including a machined piece that shapes around the round bar of the frame and makes a squared attachment point. 

Now you have this part that hangs down and swings freely as you move the canopy forward and aft. The second part is a hook shaped piece that will act as a catch. 

This piece can be attached to the side of the cockpit rail just below the canopy rail anywhere along the length of it as you desire. First I followed Matt Dralles plans and added a piece of sheet aluminum under and on top of the hook to space it just right so it aligned with the teardrop piece and give it some strength. I used the predrilled holes to match drill the sapacers. 

After I had the them drilled I clamped it in place centered between the rollbar that is right behind the pilot seat. 

I match drilled all three parts to the rail side, debuted and screwed them in place. 

So how this latch works is as you slide the canopy forward the hanging latch goes over the hook at an angle clearing the hook. You stop sliding forward at that point and slide the canopy back allowing the latch to catch on the hook.  

To clear the hook and slide the canopy all the way you just need to slide the canopy forward enough for the latch to drop down on the forward edge of the hook. Then as you slide the canopy aft the latch will angle the opposite way and pass right by the hook. 

Here is a link to a video that Matt did showing the action of the latch. This works really slick and smooth.  I’m going to add another hook somewhere forward of the first on to allow the canopy to be held open 6″ or so for taxing or when it got out as the plane sits on the ramp. 

Time: 2 Hours

With all the frame and inside skirt work done it was time to do some riveting. I put the frame back on the fuselage and bolted the two forward legs/rollers in place. The canopy was put into position with a couple cleckos on the forward loop of the frame.  I then used a Elmers glue stick to hold the small slices of rubber hose in place. 

The skirt was then put on with a couple cleckos to hold it. I then worked the skirt from aft to forward to get both the canopy and skirt to fit tight. Once I was happy with the fit all the way around I started the riveting. I started on the forward loop and worked from the top outboard left and right. 

The rivets that go through the canopy are AACQ-4-4 soft rivets to prevent cracking. I left the bottom three open as until I get the sides done. I started from aft working forward with just the soft rivets and canopy. I found that the rivet was a little tight going through the rubber hose slices. To fix that I used a little oil rubbed on the rivet to help it slide in. That worked nicely and made the job a little easier getting the rivets in place. 

After I had all the soft rivets in place I moved on to the remaining rivets which are the standard countersunk rivets since they only go through the skirt to the frame. 

So all the rivets are in place and no cracks or issues (knock on wood). So now I can work on the final outside shape of the skirt and cover up all the rivets for a nice clean look. 

Time: 2 Hours

A couple of items that needed finished before the final mounting of the skirt mounting. First was to address the haps that end up between the inside of the skirt and the frame. There is just a gap on the vertical parts of the frame. To fix this I used some quick setting epoxy to glue some washers in place. 

The second task was to adhere some felt strips around the bottom edge of the inside of the skirt. This will help seal up the canopy to the fuselage and reduce air from coming in while in flight. I borrowed the felt from Glenn and cut strips around 3/4″ wide. 

After I had all the peices cut I masked off the part of the skirts that would get the contact cement. 

Then I sprayed both the skirt and felt and let them sit to get tacky. While they say I removed all the masking. 

Once both were tacky I carefully applied the felt. It wasn’t as bad as I was planning and you have a few seconds to pull the felt off and reposition if needed. 

Hopefully this will help with the cold air coming in. We will see once we finally get in the air someday and will add more if needed. 

Time: 2 Hours

With the canopy off the frame and in the cradle I started working the holes to their final size. I am using the technique of opening the holes up and using a slice of rubber tubing as a shock absorber for the rivet. I used my plexiglass drill bit and opened all the holes to 1/4″. After that I used a dremel bit that looked like a 3/8″ ball and had a fine grit with just my fingers and not the dremel. This slowed me to put a slight chamfer on the edges and smooth them out. 

Time: 2 Hours

After cleaning up all the holes and patching I did on the frame I scuffed all the surfaces for priming followed by three coats of paint. After the paint was dry I riveted the inside skirt cover that I made in place. 

Now the frame is finished and ready for the final assembly.